Short answer: DDR5 is not just a faster DDR4. It changes the power architecture, splits each module into two sub-channels and adds on-die ECC. For most industrial and embedded boards shipping in 2026, DDR4 is still the lower-risk choice. Move to DDR5 when your processor supports it natively and your workload is limited by memory bandwidth.
DDR4 vs DDR5 at a glance
| DDR4 | DDR5 | |
|---|---|---|
| JEDEC standard | JESD79-4 | JESD79-5 |
| Core supply (VDD / VDDQ) | 1.2 V | 1.1 V |
| Data rate | 1600–3200 MT/s (JEDEC) | 4800 MT/s and up in production parts; 5600 and 6400 are common (JEDEC now defines timings up to 8800 MT/s) |
| Burst length | BL8 | BL16 |
| Banks (x4/x8) | 16 banks in 4 bank groups | 32 banks in 8 bank groups |
| Banks (x16) | 8 banks in 2 bank groups | 16 banks in 4 bank groups |
| Component density | up to 16Gb | 16Gb, 24Gb and 32Gb (the JEDEC standard covers 8Gb to 32Gb) |
| Channel per module | one 64-bit channel (72-bit with ECC) | two independent 32-bit sub-channels (40-bit each with ECC) |
| On-die ECC | No | Yes (inside the DRAM array only) |
| Module power | regulated on the motherboard | PMIC on the module (RDIMM, UDIMM, SODIMM) |
| Typical FBGA packages | 78-ball (x4/x8), 96-ball (x16) | 78-ball (x4/x8), 102-ball (x16) |
Two points cause the most confusion:
- On-die ECC is not system ECC. DDR5 corrects bit errors inside the DRAM array before data leaves the chip. It does not protect data on the bus. If your design needs end-to-end error correction, you still need ECC width (extra DRAM devices) and a memory controller that supports it.
- DDR4 and DDR5 are not interchangeable. Pinout, voltages, packages and module keying all differ. The memory controller in your SoC or CPU decides which one you can use.
When DDR4 is still the right choice
- Your platform only supports DDR4 (or DDR3L). Many ARM SoCs and previous-generation x86 embedded platforms used in industrial control, networking and video are DDR4-only.
- You need industrial temperature parts with a long track record. DDR4 has a deep range of industrial-temperature (for Micron IT parts, –40 to +95 °C case temperature; ranges differ by vendor, so check the datasheet) components from several manufacturers.
- You want low layout and power risk. DDR4 routing rules, termination and power sequencing are well understood, and most reference designs are proven in volume production.
- You need a second source. DDR4 components with the same density, organization, speed bin and temperature grade are offered by Samsung, SK hynix, Micron and Nanya, which makes dual-sourcing practical (validation is still required).
When to move to DDR5
- New platforms with native DDR5 support, such as recent edge AI boxes, embedded servers and workstation-class boards.
- Bandwidth-bound workloads: multi-stream video analytics, AI inference and packet processing where DDR4-3200 is the bottleneck.
- Higher density per device: 24Gb and 32Gb DDR5 components let you reach a target capacity with fewer chips.
If you design DDR5 memory down on the board (no module), budget extra effort for signal integrity at 4800 MT/s and above, and confirm the controller's supported data rates per topology.
Representative DDR4 and DDR5 components
All parts below have spec pages on our site. Check speed bin and temperature grade against your platform before ordering.
| Type | Part number | Brand | Key spec |
|---|---|---|---|
| DDR4 | K4A8G165WC-BIWE | Samsung | 8Gb, x16, 3200, industrial |
| DDR4 | K4AAG165WA-BCWE | Samsung | 16Gb, x16, 3200 |
| DDR4 | MT40A1G16TB-062E-IT-F | Micron | 16Gb, x16, 3200, industrial |
| DDR4 | MT40A1G8SA-062E-IT-R | Micron | 8Gb, x8, 3200, industrial |
| DDR4 | NT5AD1024M8C3-JR | Nanya | 8Gb, x8, 3200 |
| DDR5 | MT60B2G8HB-48B-A | Micron | 16Gb, x8, 4800 |
| DDR5 | MT60B1G16HD-56B-D | Micron | 16Gb, x16, 5600 |
| DDR5 | H5CG46AGBDX017 | SK hynix | 16Gb, x16, 5600 |
More parts: Samsung, SK hynix, Micron and Nanya brand pages. To read what each field of these part numbers means, see our guide on how to read DRAM part numbers.
Selection checklist
- Start from the memory controller. Confirm the supported memory type, maximum data rate, number of ranks and supported device widths (x8 or x16) in the SoC or CPU documentation.
- Match the temperature grade to the enclosure, not to the room. Fanless industrial boxes often need industrial-temperature DRAM.
- Lock the full part number, including the speed and temperature suffix. Parts with the same base number can differ in speed bin and temperature range.
- Plan the second source early. List an alternative with the same density, organization, speed bin and temperature grade, then validate it on the board (signal integrity and full-temperature testing) before production.
- Watch lifecycle notices. Ask for the manufacturer's PCN/EOL status for long-life projects and plan last-time buys where needed.
- For server memory, module type (RDIMM, LRDIMM, UDIMM) matters as much as DDR4 vs DDR5. See RDIMM vs UDIMM vs LRDIMM.
Need a cross-reference or quote?
SUNTEC (Suzhou SUNTEC Electronics Co., Ltd.) has supplied memory and semiconductor parts since 2012. Send your BOM with the platform, quantity and temperature requirement. We reply to routine inquiries within 1 business day and return a kitting proposal for complex BOMs within 2 business days. Submit your BOM.
References
- JEDEC, JESD79-4 DDR4 SDRAM standard
- JEDEC, JESD79-5D DDR5 SDRAM standard
- JEDEC, JESD79-5C update press release (2024)
- Micron, 16Gb x4/x8/x16 DDR4 SDRAM data sheet, Rev. H
- Micron, 16Gb DDR5 SDRAM addendum, die revision D