Short answer: UDIMMs connect the memory controller directly to every DRAM chip. RDIMMs add a register (RCD) that buffers command, address and clock signals. LRDIMMs also buffer the data lines. Each step lowers the electrical load on the memory channel, so you can install more and larger modules per channel. Use UDIMMs (or SODIMMs) for desktops, workstations and most industrial PCs; RDIMMs for mainstream servers; and LRDIMMs only when you need the highest capacity per server. Never mix the types: a platform supports one kind, and mixed configurations will not boot.
What the buffer does
- UDIMM (unbuffered): command and address lines from the controller fan out to every DRAM device on the module. Each extra device adds load, which limits how many modules and ranks one channel can carry at full speed.
- RDIMM (registered): a Registering Clock Driver (RCD) on the module re-drives command, address, control and clock signals. The controller sees one load per module instead of many. Data lines still connect directly to the DRAM.
- LRDIMM (load-reduced): adds data buffers between the controller and the DRAM, so data lines are buffered too. This allows very high capacity modules (often built with 3DS stacked DRAM) while keeping usable speeds when a channel is fully populated.
Comparison table
| UDIMM / SODIMM | RDIMM | LRDIMM | |
|---|---|---|---|
| Buffering | none | RCD on command/address/clock | RCD + data buffers |
| ECC | optional (ECC UDIMM exists) | standard | standard |
| Typical DDR4 capacity per module | 4–32 GB | 8–64 GB (3DS RDIMMs up to 256 GB) | 64–256 GB |
| Load per channel | highest | lower | lowest |
| Latency | lowest | slightly higher | slightly higher than RDIMM |
| Typical platforms | desktops, workstations, industrial PCs, laptops (SODIMM) | general servers, virtualization, databases | maximum-memory servers, in-memory analytics |
| Pins (DDR4 / DDR5) | UDIMM 288 / 288; SODIMM 260 / 262 | 288 / 288 | 288 (DDR4); rare in DDR5 |
ECC vs non-ECC memory
Non-ECC modules carry 64 data bits per channel. ECC modules add check bits so the memory controller can correct at least single-bit errors and detect double-bit errors (SECDED); many server platforms layer stronger schemes such as Chipkill/SDDC on top:
- DDR4: 72-bit modules (64 data + 8 ECC).
- DDR5: each module has two 32-bit sub-channels; the common ECC configuration (EC8) makes each sub-channel 40 bits (32 + 8).
Server RDIMMs and LRDIMMs are ECC by design. ECC UDIMMs are used in entry servers, edge servers, medical and financial terminals, but only work as ECC if the CPU and motherboard support it. DDR5's on-die ECC is a separate mechanism inside each DRAM chip and does not replace module-level ECC. See DDR4 vs DDR5 for details.
DDR4 vs DDR5 server modules
DDR5 RDIMMs move power regulation onto the module with a PMIC, split the module into two sub-channels and start at 4800 MT/s. DDR4 and DDR5 modules are keyed differently and are not interchangeable. In DDR5, RDIMMs and UDIMMs are also keyed differently and are electrically different: the RDIMM PMIC takes a 12 V input, while client UDIMMs and SODIMMs use 5 V. (DDR4 RDIMMs and UDIMMs share the same key position but are still not electrically compatible.) In the DDR5 generation, LRDIMMs are rare; high capacities are built as 3DS RDIMMs or MRDIMMs. The CPU generation decides which one you need.
Representative server and client modules
| Type | Part number | Brand | Key spec |
|---|---|---|---|
| DDR4 RDIMM | HMA82GR7DJR4N-XN | SK hynix | 16 GB, 3200, 1Rx4 |
| DDR4 RDIMM | MTA9ASF2G72PZ-3G2F1 | Micron | 16 GB, 3200, 1Rx8 |
| DDR4 RDIMM | HMAA4GR7CJR8N-XN | SK hynix | 32 GB, 3200, 2Rx8 |
| DDR4 RDIMM | MTA36ASF4G72PZ-3G2R1 | Micron | 32 GB, 3200, 2Rx4 |
| DDR4 RDIMM | M393A8G40AB2-CWE | Samsung | 64 GB, 3200, 2Rx4 |
| DDR4 LRDIMM | M386AAG40BM3-CWE | Samsung | 128 GB, 3200, 4DRx4 (3DS) |
| DDR5 RDIMM | MTC10F1084S1RC48BA1 | Micron | 16 GB, 4800, 1Rx8 |
| DDR5 RDIMM | HMCG78AGBRA | SK hynix | 16 GB, 5600, 1Rx8 |
| DDR5 RDIMM | MTC40F2046S1RC56BD1 | Micron | 64 GB, 5600, 2Rx4 |
| DDR5 RDIMM | MTC40F2047S1RC64BB1 | Micron | 128 GB, 6400, 2Rx4 (32Gb DRAM) |
| DDR4 UDIMM | M378A2G43CB3-CWE | Samsung | 16 GB, 3200 |
| DDR4 UDIMM | MTA8ATF1G64AZ-3G2R1 | Micron | 8 GB, 3200 |
| DDR4 SODIMM | M471A2G43CB2-CWE | Samsung | 16 GB, 3200 |
Rank and die revision differ between part numbers even at the same capacity. Check the platform's qualified vendor list (QVL) before ordering. More modules: Samsung, SK hynix, Micron.
Selection checklist
- Follow the platform QVL. CPU and motherboard vendors publish qualified memory lists. Match type, capacity, rank and speed bin.
- Count ranks per channel. The controller limits ranks per channel, and speed often drops as you add modules. LRDIMMs hold speed better at full population.
- Fill channels evenly. Populate every channel with identical modules to get full bandwidth before adding a second module per channel.
- Do not mix module types. RDIMM, LRDIMM and UDIMM cannot be combined. Even within RDIMMs, mixing capacities, ranks or brands can lower speed or fail to train.
- Keep spares from the same lot. For fleet servers, buying the same part number and lot simplifies validation and repair.
- Plan the DDR5 transition by platform. Extend existing DDR4 servers with the same modules; specify DDR5 RDIMMs for new platforms.
Need server memory or a cross-reference?
SUNTEC supplies DDR4 and DDR5 RDIMMs, LRDIMMs, UDIMMs and SODIMMs from Samsung, SK hynix and Micron. Send the server model or CPU platform, capacity and quantity; we reply within 1 business day and can propose same-spec alternatives across the three DRAM makers. Submit your BOM.
References
- JEDEC, DDR5 memory module design files
- Rambus, DDR5 server PMICs and DDR5 client PMICs
- Samsung Semiconductor, DDR4 DRAM modules
- Kingston, DDR5 overview (MKF_954)