K4AAG165WA-BCWE is a candidate for a capacity upgrade from K4A8G165WC-BCWE only if the board, memory controller, and firmware support 16 Gb x16 devices and the new configuration passes board validation. Both parts are DDR4-3200 x16 devices in 96-ball FBGA packages, but the 16 Gb part uses one more row address bit. For a repair or a repeat build against the existing bill of materials (BOM), order the approved 8 Gb part unless an engineering change has released the 16 Gb configuration.
1. Compare density and addressing
Samsung’s DDR4 product guide lists these devices at the same nominal 1.2 V core supply and in the same 96-ball FBGA package class. The x16 designation means that each device has a 16-bit data interface. The difference is in how many locations the controller can address through that interface. The 8 Gb device is organized as 512M × 16, while the 16 Gb device is organized as 1G × 16.
| Check | K4A8G165WC-BCWE | K4AAG165WA-BCWE |
|---|---|---|
| Density and organization | 8 Gb, 512M × 16 | 16 Gb, 1G × 16 |
| Data rate and package | 3200 MT/s, 96-ball FBGA | 3200 MT/s, 96-ball FBGA |
| Row address | A0–A15 | A0–A16 |
| Columns and bank groups | A0–A9, 2 groups of 4 banks | A0–A9, 2 groups of 4 banks |
In a board configuration where two x16 devices operate in parallel on a 32-bit data path, two 8 Gb devices provide 2 GiB of physical capacity. Two 16 Gb devices provide 4 GiB if the controller can use the full arrays. The data path is still 32 bits wide, and usable memory reported by the operating system may be lower because some address space is reserved. Use the device density when specifying the part and the board capacity when describing the finished assembly.
The 3200 MT/s figure identifies the devices’ rated transfer rate. Whether an assembly runs at that rate depends on the controller, the board design, and the configuration used on that build. Compare the rate you actually need to qualify with the rate observed during testing.
2. Check the board, controller, and firmware
Start with the exact board revision and the memory controller’s supported device organizations. Look for support for 16 Gb x16 DDR4 with the channel and chip select arrangement on that board. A system specification that gives only a maximum memory capacity does not tell you whether the controller can address a 16 Gb chip in that layout. Where multiple BOM variants use the same PCB, ask which assembly and firmware combination has been released for the higher density.
Next, compare the manufacturer’s ball maps and mechanical drawings with the schematic and land pattern. Samsung’s 16 Gb A-die pinout identifies ball L8 as RAS_n/A16. The extra row address bit uses that multiplexed signal. The density change does not imply that you need a new dedicated A16 pad. Confirm that the controller and the existing connection can deliver the bit during row activation. Also check the land pattern, body outline, and clearance for the actual devices rather than signing off on the ball count.
Finally, identify the memory initialization settings loaded by the firmware on the target assembly. Check the device density and address mapping, and confirm that timing and refresh settings follow the applicable part and operating conditions. On boards that select profiles using assembly straps or another board identifier, verify which profile the test unit actually loads. An 8 Gb firmware profile that already boots on the PCB is not evidence that the 16 Gb configuration is supported.
Keep these checks separate in the engineering record. A controller can support the density while a particular firmware build lacks the matching profile. Likewise, correct firmware cannot resolve a physical connection or assembly issue. Recording which check has passed makes it easier to decide whether to order samples or keep the original BOM.
If the platform documentation is unclear, ask the board owner for the approved memory population and initialization profile before buying production quantities. For instance, a 16 Gb configuration on a different revision may use the same PCB outline but a different assembly option or firmware image. Record whether you are qualifying a new configuration or reproducing an already approved one. The evidence needed to place the order is different.
3. Validate the added address range and operating behavior
On the sample board, record the detected capacity, actual transfer rate, and memory training result before running a load test. Use an approved diagnostic on the sample board to test the address range added by the upgrade. Keep these write tests off production equipment. To check for address aliasing, use the controller’s address map to select two test locations with the same channel, rank, bank, and column whose expected row addresses differ only in A16. Write different patterns and read both back after writing each location. This helps detect a case where a write to the added address range also changes data in the original range.
| Sample-board check | Evidence to retain |
|---|---|
| Capacity and data rate | Firmware configuration, detected capacity, actual transfer rate |
| Added address range | Addresses or ranges exercised, test patterns, and readback results |
| Startup and sustained load | Startup, restart, and load-test results under project conditions |
| Production release | Approved full part number, board revision, firmware version, and release scope |
Use a memory test that exercises DRAM rather than only checking the size reported by firmware. Some test environments cannot reach reserved regions. Document what the test covered instead of describing it as a full-memory pass. If the board boots with the expected capacity but reports intermittent errors, compare training and configured timing and refresh with the approved settings before attributing the failure to the part or the solder joints.
Exercise the board under the startup and sustained load conditions relevant to the product. Depending on the project, that can include power-on from a cold state, a warm restart, and a sustained memory workload. Keep the board and firmware identifiers with the results so a successful sample test cannot be mistaken for approval of another production variant.
Treat that targeted check as one part of validation. Select multiple address pairs and use a diagnostic that reaches DRAM so that cached reads do not mask an alias. Exercise the rest of the accessible memory too. Passing one pair tells you that the selected addresses did not alias in that test, but says little about sustained load or other regions.
4. Keep repeat orders separate from the capacity upgrade
If the approved BOM specifies K4A8G165WC-BCWE, keep the repair or repeat purchase on that line. Quote K4AAG165WA-BCWE separately as an evaluation part until engineering approves the new configuration. A quote labeled only “Samsung DDR4-3200 x16” leaves out the density and exact orderable part, so ask for a corrected line before placing the order. Once the change is released, make the approved board and firmware scope clear in the purchase record.
At receiving, match the complete manufacturer part number and label to the purchase order and keep the lot record. If a package top mark is abbreviated, use the DRAM part number and marking guide to find the appropriate manufacturer information, then cross-check the full number on the packaging label. Hold a shipment with a density or part-number discrepancy pending disposition. A stock shortage may justify evaluating a new configuration, but it does not change what the existing purchase order accepts.
For a DDR4 capacity upgrade, record both full part numbers, the board revision, and how many devices each assembly uses. When reviewing the candidate quote, include the controller support, sample test status, and scope of any release. If you need separate sample and production quotes, send SUNTEC the part numbers, quantities, and target delivery date.
Prepared by the SUNTEC Technical Team at Suzhou SUNTEC Electronics Co., Ltd.