Find listed NOR flash part numbers and compare interface, operating voltage, density and package for the intended host.
Serial NOR is used for code storage, but the usable read or execution mode depends on the device and host. Winbond lists different QSPI families and voltage options. Check the full suffix, supported commands, I/O voltage and package against the design; a 1.8 V part and a 3 V part are separate selection choices.
| Selection dimension | Check for the complete part number |
|---|---|
| Host and mode | Serial bus width, commands and execution support |
| Electrical conditions | Supply and I/O voltage for the full ordering code |
| Physical requirements | Density, package, pin assignment and temperature grade |
Manufacturer references: Winbond QSPI NOR
Part numbers: 85 · Page 4 / 4
| Part No. | Brand | Series | Specification | Application | Quote |
|---|---|---|---|---|---|
| MX66L1G45GMI-10G | Macronix | MX66L (High-density / Octal) | 1Gb | High-density code storage | Quote → |
| MX29LV160DBTI-70G | Macronix | MX29LV (Parallel NOR) | 16Mb parallel NOR | Industrial / legacy platforms | Quote → |
| GD25Q80ETIG | GigaDevice | GD25Q (3V SPI NOR) | 8Mb SPI NOR Flash, 133MHz, SOP-8 150mil, 2.7~3.6V, industrial -40~85°C | Code / parameter storage for MCUs, small appliances, IoT modules | Quote → |
| GD25Q16ETIG | GigaDevice | GD25Q (3V SPI NOR) | 16Mb SPI NOR Flash, 133MHz, SOP-8 150mil, 2.7~3.6V, industrial -40~85°C | MCU code storage, Bluetooth / Wi-Fi modules, small appliances | Quote → |
| GD25Q32ESIG | GigaDevice | GD25Q (3V SPI NOR) | 32Mb SPI NOR Flash, 133MHz, SOP-8 208mil, 2.7~3.6V, industrial -40~85°C | IoT module firmware, display font storage, consumer code storage | Quote → |
| GD25Q64ESIG | GigaDevice | GD25Q (3V SPI NOR) | 64Mb SPI NOR Flash, 133MHz, SOP-8 208mil, 2.7~3.6V, industrial -40~85°C | Firmware storage for networking, set-top boxes and industrial control | Quote → |
| GD25Q128ESIG | GigaDevice | GD25Q (3V SPI NOR) | 128Mb SPI NOR Flash, 133MHz, SOP-8 208mil, 2.7~3.6V, industrial -40~85°C | Firmware storage for industrial control, networking and IoT | Quote → |
| GD25Q256EYIG | GigaDevice | GD25Q (3V SPI NOR) | 256Mb SPI NOR Flash, 133MHz, WSON-8 8×6mm, 2.7~3.6V, industrial -40~85°C | Boot and firmware storage for routers, IP cameras and industrial boards | Quote → |
| GD25LQ128ESIG | GigaDevice | GD25LQ (1.8V SPI NOR) | 128Mb SPI NOR Flash, 133MHz, SOP-8 208mil, 1.65~2.0V, industrial -40~85°C | Firmware storage on 1.8V SoC platforms (modules, wearables, mobile accessories) | Quote → |
| GD25LE128ESIG | GigaDevice | GD25LE (1.8V low-power SPI NOR) | 128Mb SPI NOR Flash, 133MHz, SOP-8 208mil, 1.65~2.0V, industrial -40~85°C | Code storage for wearables, TWS earbuds and battery-powered IoT devices | Quote → |
| GD25B512MFYIG | GigaDevice | GD25B (3V SPI NOR, Quad by default) | 512Mb SPI NOR Flash, 133MHz, WSON-8 8×6mm, 2.7~3.6V, industrial -40~85°C | Large firmware images, FPGA configuration, boot storage for networking and security devices | Quote → |
| GD25LX256EBIR | GigaDevice | GD25LX (1.8V Octal SPI NOR) | 256Mb SPI NOR Flash (Octal DTR), 200MHz, TFBGA-24, 1.65~2.0V, industrial -40~85°C | High-speed boot and XiP for AIoT, display terminals and industrial HMI | Quote → |
| GD25LX512MEBIR | GigaDevice | GD25LX (1.8V Octal SPI NOR) | 512Mb SPI NOR Flash (Octal DTR), 200MHz, TFBGA-24, 1.65~2.0V, industrial -40~85°C | High-density high-speed boot and XiP for AIoT, display terminals and industrial HMI | Quote → |
NOR vs NAND flash compared: random reads, XIP, erase blocks, endurance, bad blocks and ECC, and when to use SPI NOR, SPI NAND or parallel NAND.
Octal SPI (xSPI) NOR reaches 400 MB/s at 200 MHz DTR. When to leave Quad SPI, what the MCU must support, and Winbond W35T, GigaDevice GD25LX, Micron MT35X.
Include quantities and the requirements that matter for your design.