Short answer: Move from Quad SPI NOR to Octal SPI NOR when the processor runs code directly from flash (execute in place, XIP) and Quad SPI bandwidth has become the bottleneck, or when you want to drop a DRAM that only exists to hold a copy of the code. Octal parts use eight data lines and, in double transfer rate (DTR) mode at 200 MHz, read at up to 400 MB/s. Winbond rates its W35T Octal NOR at five times its W25Q Quad SPI NOR. Before choosing a part, confirm that the MCU has an Octal controller with DTR and data strobe support, and that its I/O voltage matches; most Octal NOR runs at 1.8 V.
Quad SPI vs Octal SPI NOR
Octal SPI NOR is still NOR flash. What changes is the interface: eight data lines instead of four, double-edge transfers and a data strobe for high-speed reads. JEDEC standardizes this interface as xSPI (JESD251).
| Quad SPI NOR | Octal SPI NOR | |
|---|---|---|
| Data lines | 4 | 8 |
| Typical read clock | about 104–133 MHz, mostly single transfer rate (STR) | up to 200 MHz with DTR (166 MHz STR on Winbond W35T) |
| Sequential read | roughly 50–80 MB/s, depending on clock and DTR support | up to 400 MB/s at 200 MHz DTR |
| Data strobe | none | DQS (also called RWDS), needed for high-speed DTR reads |
| Common I/O voltage | 3.3 V, with 1.8 V versions | mostly 1.8 V |
| Host controller | any Quad SPI controller | an Octal / xSPI controller |
| Typical use | boot code, small firmware, parameters | fast XIP, instant-on, replacing code-shadowing DRAM |
Common Quad SPI families are Winbond W25Q, GigaDevice GD25Q and Micron MT25Q. The Octal counterparts are Winbond W35T, GigaDevice GD25LX and Micron MT35X (Xccela).
Why XIP is the reason to switch
In many MCU and SoC designs, code is copied from slow flash into DRAM at boot and runs from there. That costs boot time and a DRAM device. With 400 MB/s reads and a cache in front of the flash, many designs can execute directly from Octal NOR instead, which removes the copy step and, in smaller memory systems, the DRAM that only held code. That architectural saving, more than raw speed, is the usual case for Octal NOR.
STR, DTR and the data strobe
STR transfers data on one clock edge; DTR transfers on both. The 400 MB/s figure needs DTR: 200 MHz × 2 transfers per clock × 8 bits = 400 MB/s. At these rates the host samples data against the DQS strobe the flash drives back, so the controller must support DTR and DQS, and the PCB must keep CLK, DQS and data lines matched. If the controller only runs STR, or cannot close timing at 200 MHz, the real throughput is much lower.
Representative Octal SPI NOR parts
| Maker | Part | Density | Clock (STR / DTR) | Voltage, package | Notes |
|---|---|---|---|---|---|
| Winbond | W35T51NW | 512 Mb | 166 MHz / 200 MHz | 1.8 V, BGA24 | W35T family: JEDEC xSPI, 400 MB/s |
| Winbond | W35T01NW | 1 Gb | 166 MHz / 200 MHz | 1.8 V, BGA24 | Same family, higher density |
| GigaDevice | GD25LX256E | 256 Mb | 200 MHz (x1, x8) / 200 MHz (x8 DTR) | 1.8 V; SOP16, TFBGA24, WLCSP | JESD251 compliant; –40 to +85, +105 or +125 °C options |
| GigaDevice | GD25LX512ME | 512 Mb | 200 MHz class | 1.8 V | GD25LX family |
| Micron | MT35XU512ABA | 512 Mb | 200 MHz | 1.8 V, 24-ball BGA | Xccela family |
Densities above 128 Mb need 4-byte addressing, so check that both the controller and the driver are configured for it. Confirm speed grade, temperature grade and package against the datasheet of the exact order code.
Six checks before you choose
- Controller: the MCU or SoC needs an Octal / xSPI controller, such as ST's OCTOSPI or NXP's FlexSPI on i.MX RT. A Quad-only MCU cannot use an Octal part in Octal mode.
- I/O voltage: most Octal NOR runs at 1.8 V. Match it to the controller's I/O supply domain.
- DTR and DQS: to reach 400 MB/s, the controller must run DTR and sample DQS, and the layout must keep the high-speed lines matched.
- Density and addressing: 256 Mb and above means 4-byte addresses in the boot ROM, driver and programming tools.
- Package and ball map: BGA24 is common, and some parts also come in SOP16. Check the pinout against your board before treating parts as interchangeable.
- Reliability and temperature: review ECC, endurance and retention in the datasheet, and pick the industrial or automotive grade your product needs.
Second-sourcing Octal NOR
Matching density, voltage and package is not enough. Octal NOR from different makers can differ in command set, dummy-cycle settings, power-up mode (STR or DTR) and how DTR is entered, so a second source usually needs driver or boot ROM configuration work and full validation on the target controller. Plan that work early, and check the controller vendor's list of validated flash devices.
Send us your requirements
Tell us the controller, I/O voltage, density, package, temperature grade and yearly volume. We will suggest Octal or Quad NOR candidates and second-source options. We reply to routine inquiries within 1 business day and return a matched proposal for complex BOMs within 2 business days. Submit your BOM.