Find listed NOR flash part numbers and compare interface, operating voltage, density and package for the intended host.
Serial NOR is used for code storage, but the usable read or execution mode depends on the device and host. Winbond lists different QSPI families and voltage options. Check the full suffix, supported commands, I/O voltage and package against the design; a 1.8 V part and a 3 V part are separate selection choices.
| Selection dimension | Check for the complete part number |
|---|---|
| Host and mode | Serial bus width, commands and execution support |
| Electrical conditions | Supply and I/O voltage for the full ordering code |
| Physical requirements | Density, package, pin assignment and temperature grade |
Manufacturer references: Winbond QSPI NOR
Part numbers: 85 · Page 1 / 4
| Part No. | Brand | Series | Specification | Application | Quote |
|---|---|---|---|---|---|
| N25Q064A13ESED0F | Micron | NOR Flash | Nor Flash, 64Mb, 2.7~3.6V, 65nm, SOP2 | Quote → | |
| JS28F256J3F105A | Micron | NOR Flash | Nor Flash, 256Mb, MLC, TSOP | Quote → | |
| JS28F256P33BFE | Micron | NOR Flash | Nor Flash, 256Mb, MLC, TSOP, 2.3 - 3.6 V, Bottom Boot | Quote → | |
| MT25QL128ABA1ESE-0SIT | Micron | NOR Flash | Nor Flash, SPI, 128Mb, SOIC, 3V, 160MTPS | Quote → | |
| MT25QU128ABA1ESE-0SIT | Micron | NOR Flash | Nor Flash, SPI, 128Mb, SOIC, 1.8V, 160MTPS | Quote → | |
| MT25QL128ABA8ESF-0SIT | Micron | NOR Flash | Nor Flash, SPI, 128Mb, SOIC, 3V, 160MTPS | Quote → | |
| MT25QL128ABA8E12-0SIT | Micron | NOR Flash | Nor Flash, SPI, 128Mb, 160MTPS | Quote → | |
| MT25QL128ABA1EW9-0SIT | Micron | NOR Flash | Nor Flash, SPI, 128Mb, WPDFN, 3V, 160MTPS | Quote → | |
| MT25QL128ABA1EW7-0SIT | Micron | NOR Flash | Nor Flash, SPI, 128Mb, WPDFN, 3V, 160MTPS | Quote → | |
| MT25QU128ABA1EW7-0SIT | Micron | NOR Flash | Nor Flash, SPI, 128Mb, WPDFN, 1.8V, 160MTPS | Quote → | |
| MT25QU128ABA1EW9-0SIT | Micron | NOR Flash | Nor Flash, SPI, 128Mb, 1.8V, 160MTPS | Quote → | |
| MT25QL256ABA8ESF-0SIT | Micron | NOR Flash | Nor Flash, SPI, 256Mb, SOIC, 3V, 160MTPS | Quote → | |
| MT25QU256ABA8ESF-0SIT | Micron | NOR Flash | Nor Flash, SPI, 256Mb, SOIC, 1.8V, 160MTPS | Quote → | |
| MT25QL256ABA1EW9-0SIT | Micron | NOR Flash | Nor Flash, SPI, 256Mb, WPDFN, 3V, 160MTPS | Quote → | |
| MT25QL256ABA8E12-1SIT | Micron | NOR Flash | Nor Flash, SPI, 256Mb, TBGA, 3V, 160MTPS | Quote → | |
| MT25QL256ABA1EW7-0SIT | Micron | NOR Flash | Nor Flash, SPI, 256Mb, WPDFN, 3V, 160MTPS | Quote → | |
| MT25QU256ABA1EW7-0SIT | Micron | NOR Flash | Nor Flash, SPI, 256Mb, WPDFN, 1.8V, 160MTPS | Quote → | |
| MT25QU256ABA1EW9-0SIT | Micron | NOR Flash | Nor Flash, SPI, 256Mb, WPDFN, 1.8V, 160MTPS | Quote → | |
| MT25QL512ABB8ESF-0SIT | Micron | NOR Flash | Nor Flash, SPI, 512Mb, SOIC, 3V, 160MTPS | Quote → | |
| MT25QU512ABB8ESF-0SIT | Micron | NOR Flash | Nor Flash, SPI, 512Mb, SOIC, 1.8V, 160MTPS | Quote → | |
| MT25QL512ABB8E12-0SIT | Micron | NOR Flash | Nor Flash, SPI, 512Mb, TBGA, 3V, 160MTPS | Quote → | |
| MT25QU512ABB8E12-0SIT | Micron | NOR Flash | Nor Flash, SPI, 512Mb, TBGA, 1.8V, 160MTPS | Quote → | |
| MT25QL01GBBB8ESF-0AAT | Micron | NOR Flash | Nor Flash, SPI, 1Gb, SOIC, 3V, 160MTPS, Auto. | Quote → | |
| MT25QL01GBBB8ESF-0SIT | Micron | NOR Flash | Nor Flash, SPI, 1Gb, SOIC, 3V, 160MTPS | Quote → |
NOR vs NAND flash compared: random reads, XIP, erase blocks, endurance, bad blocks and ECC, and when to use SPI NOR, SPI NAND or parallel NAND.
Octal SPI (xSPI) NOR reaches 400 MB/s at 200 MHz DTR. When to leave Quad SPI, what the MCU must support, and Winbond W35T, GigaDevice GD25LX, Micron MT35X.
Do not treat the names as equivalent. Winbond distinguishes Quad SPI, where the command uses one signal line, from QPI, where command, address and data use four lines. Check the exact device's supported modes and the host's command format before specifying a NOR part for the design.
Review the electrical design first. Winbond lists 1.8 V and 3 V NOR as separate voltage options. Check the full ordering code's operating supply range and input/output limits against the board and host. Matching capacity or package does not establish that the electrical conditions are suitable.
Check the exact pin-function and Quad Enable descriptions. SPI NOR devices can share /WP and /HOLD or /RESET pins with IO2 and IO3, so a control signal used in single SPI operation may change function in quad operation. Review board wiring and startup configuration before selecting the ordering code.
Include quantities and the requirements that matter for your design.