Short answer: Kioxia and Micron do not publish a TBW (terabytes written) figure for the eMMC parts below, so the practical way to know how much life a deployed eMMC has left is to read the health fields the device reports about itself: PRE_EOL_INFO and DEVICE_LIFE_TIME_EST in the Extended CSD register (eMMC 5.0 and later). For new designs, the most common mistake is the temperature grade: parts with the same eMMC version and the same 11.5 × 13 mm body can be consumer or industrial grade.
Why there is no TBW to look up
Kioxia and Micron have not published total bytes written or program/erase cycle figures for the parts in this article. Micron's industrial eMMC datasheets state that NAND endurance is defined by the applicable qualification documents and by the health information described in its technical notes, and that qualification and reliability reports are available to customers on request.
Kioxia explains why a static number would not help much anyway: TBW figures can be inaccurate for e-MMC and UFS lifetime estimates when the real workload differs from the JEDEC or vendor workload used to calculate them. The reliable method is to read the device's own wear estimate and project it with your measured write rate.
Reading the health registers in EXT_CSD
Since eMMC 5.0, JEDEC defines three read-only bytes in the 512-byte Extended CSD register:
| EXT_CSD byte | Field | What it reports |
|---|---|---|
| 267 | PRE_EOL_INFO | Consumption of reserved blocks: 01h normal (under 80% used), 02h warning (80% used), 03h urgent (90% used); 00h not defined |
| 268 | DEVICE_LIFE_TIME_EST_TYP_A | Estimated life used, based on the average wear of Type A (SLC) memory |
| 269 | DEVICE_LIFE_TIME_EST_TYP_B | Estimated life used, based on the average wear of Type B (MLC) memory |
The two life estimates use the same scale: 01h means 0–10% of the estimated life used, 02h means 10–20%, and so on up to 0Ah for 90–100%. 0Bh means the device has exceeded its estimated lifetime, and 00h means not defined. Kioxia's wear-leveling tech brief points to DEVICE_LIFE_TIME_EST (EXT_CSD slice 268) as the place to read e-MMC lifetime, and notes that the estimate is meaningful because the device levels wear across its blocks.
On Linux, mmc extcsd read /dev/mmcblk0 from mmc-utils prints these fields, and the kernel also exposes pre_eol_info and life_time in sysfs for the eMMC device. Underneath, the host sends CMD8 (SEND_EXT_CSD) and reads bytes 267–269 of the returned block.
Micron adds a vendor health report on top of the JEDEC fields. Its eMMC device health report technical notes (listed on Micron's eMMC software page) describe data read with the general command CMD56, such as bad block counts, remaining spare blocks and erase-count statistics for the SLC and MLC areas. Use the three JEDEC bytes for routine field monitoring and the vendor report for failure or batch analysis.
A practical rule for fleets: log the three values per unit and per batch, and schedule replacement when PRE_EOL_INFO reaches 02h or a life estimate reaches 08h, rather than waiting for write errors.
Temperature grade: same package, different rating
| Part number | Maker | Capacity | eMMC | Operating temperature | Grade |
|---|---|---|---|---|---|
| THGBMJG6C1LBAU7 | Kioxia | 8 GB | 5.1 | –40 to +105 °C (Kioxia also lists a 115 °C case limit) | Industrial |
| THGAMVG7T13BAIL | Kioxia | 16 GB | 5.1 | –25 to +85 °C | Consumer |
| THGAMVG8T13BAIL | Kioxia | 32 GB | 5.1 | –25 to +85 °C | Consumer |
| MTFC16GAPALBH-IT | Micron | 16 GB | 5.1 (MLC) | –40 to +85 °C | Industrial (IT) |
| MTFC64GAPALBH-AAT | Micron | 64 GB | 5.1 (MLC) | –40 to +105 °C ambient, case up to 115 °C | Automotive (AAT) |
All five use an 11.5 × 13 mm body. The three Kioxia parts look interchangeable by version, size and maker, but Kioxia lists THGBMJG6C1LBAU7 under industrial grade and the 16 GB and 32 GB parts under consumer grade. Using the consumer parts in a fanless or outdoor enclosure can push them past their range on a hot day.
Micron encodes the grade in the suffix. Its eMMC part numbering guide defines: no suffix, 0 to +70 °C; WT, –25 to +85 °C; IT, industrial –40 to +85 °C; AIT, industrial –40 to +85 °C with an additional HR qualification flow. AAT is defined in Micron's automotive datasheets as –40 to +105 °C ambient (Ta) with a 115 °C maximum case temperature; AIT there carries a 95 °C case maximum. The WT and IT MLC datasheets give only the operating range without stating whether it is ambient or case temperature, so confirm the reference point early if your thermal margin is tight.
Lifecycle: when we checked Micron's part catalog in September 2026, both Micron parts in the table were listed as obsolete. Confirm the current status of any eMMC before you design it in.
What to do with this
- New fanless or outdoor design: start from industrial-grade parts, such as THGBMJG6C1LBAU7 for 8 GB. For larger capacities choose another industrial-grade part instead of THGAMVG7T13BAIL or THGAMVG8T13BAIL.
- Indoor, temperature-controlled design: THGAMVG7T13BAIL (16 GB) and THGAMVG8T13BAIL (32 GB) are reasonable capacity points within –25 to +85 °C.
- Products already in the field: read PRE_EOL_INFO and both life estimates, record them by batch and plan replacements from the trend.
- Designs using discontinued Micron eMMC: plan the replacement window now and qualify an alternative while the original parts can still be sourced.
More on NAND wear and pSLC modes in SLC vs MLC vs TLC vs QLC, and on the interface choice in eMMC vs UFS. Browse eMMC on the Kioxia and Micron pages.
Send us your conditions and readings
Tell us the capacity you need, the real temperature inside the enclosure, the daily write volume and the PRE_EOL_INFO and DEVICE_LIFE_TIME_EST values from units in the field. We will suggest candidates in the right temperature grade and sourcing options for discontinued parts. We reply to routine inquiries within 1 business day. Submit your BOM.
References
- JEDEC, JESD84-B51 eMMC 5.1 standard (Extended CSD fields PRE_EOL_INFO and DEVICE_LIFE_TIME_EST)
- Kioxia, Understanding Wear Leveling in NAND Flash Memory (tech brief)
- Kioxia, Understanding TBW versus P/E Cycles in Managed Flash Memory (tech brief)
- Micron, eMMC software and technical notes (device health report notes)
- Micron, obsolete e.MMC part catalog