Short answer: SLC, MLC, TLC and QLC describe how many bits each NAND flash cell stores: one, two, three or four. More bits per cell lowers the cost per gigabyte but narrows the voltage window between states, which reduces endurance, slows writes and raises ECC requirements. For small boot and data devices in industrial equipment, SLC NAND is still the reference. For gigabyte-class storage, 3D TLC inside eMMC, UFS or an SSD is the mainstream choice, with pSLC mode or careful write budgeting when endurance matters.
The four NAND cell types compared
| Type | Bits per cell | Typical P/E endurance* | Write speed | Cost per GB | Typical use |
|---|---|---|---|---|---|
| SLC | 1 | typically 100,000 for raw SLC NAND (at the ECC level stated in the datasheet) | fastest | highest | boot code, industrial data logging, telecom, medical |
| MLC | 2 | about 3,000–10,000 | fast | high | industrial eMMC and SSDs (being replaced by TLC/pSLC) |
| TLC | 3 | about 1,000–3,000 (3D TLC) | moderate | low | eMMC, UFS, SSDs, memory cards: today's mainstream |
| QLC | 4 | a few hundred to about 1,000 | slowest | lowest | read-intensive, high-capacity storage and archives |
*Order-of-magnitude figures. Endurance depends on the process, the ECC used and the retention requirement. Always use the rating in the datasheet of the exact part.
Why more bits per cell means less endurance
A NAND cell stores data as charge on a charge-trap or floating-gate layer. SLC only has to tell two charge levels apart. TLC must separate eight levels and QLC sixteen inside a similar voltage range. Each program/erase cycle slightly wears the cell, so the narrow margins of TLC and QLC are lost sooner. That is also why higher-density NAND needs stronger ECC and why data retention drops as a device approaches its rated cycle count, especially at high temperature.
3D NAND changed the trade-off
Planar (2D) NAND ran into scaling limits, and the industry moved to 3D NAND, which stacks cells vertically. Samsung began mass-producing 3D V-NAND in 2013, and the other manufacturers followed in 2015–2016. Current products exceed 200 layers; for example, SK hynix 321-layer and Micron 276-layer NAND entered production in 2024. Each manufacturer has its own name for it: Samsung V-NAND, Kioxia and SanDisk BiCS FLASH, and the 3D NAND generations from Micron and SK hynix.
Stacking let each cell be larger again, which made 3D TLC far more durable than late-generation 2D TLC. That is the main reason TLC became the default in managed NAND. More layers mostly lower cost per bit; they do not by themselves make a part more reliable.
SLC NAND is still alive in industrial designs
At 1Gb to 16Gb, raw SLC NAND remains a common choice for bootloaders, file systems on Linux-based controllers, and critical data in long-life equipment. Representative parts:
| Part number | Brand | Interface | Density |
|---|---|---|---|
| TC58NVG0S3HBAI4 | Kioxia | parallel | 1Gb SLC, –40 to +85 °C, host ECC |
| TC58NVG2S0HBAI4 | Kioxia | parallel | 4Gb SLC, industrial |
| TH58NVG3S0HTAI0 | Kioxia | parallel | 8Gb SLC |
| MT29F4G08ABADAWP-IT-D | Micron | parallel | 4Gb SLC, industrial, rated 100,000 cycles, optional on-die ECC |
| MT29F16G08ABACAWP-ITZ-C | Micron | parallel | 16Gb SLC |
| W25N01GVZEIG | Winbond | SPI | 1Gb SLC, rated over 100,000 cycles, on-die ECC |
| MT29F2G01ABAGDWB-IT-G | Micron | SPI | 2Gb SLC, industrial |
More SLC NAND on the Kioxia, Micron, Macronix and Winbond pages.
Raw NAND needs the host to handle ECC, bad-block management and wear leveling. Managed NAND such as eMMC and UFS does that inside the package; see eMMC vs UFS. For code storage, compare NOR vs NAND flash.
pSLC: SLC-like endurance from TLC or MLC
pSLC (pseudo-SLC) is a firmware mode that stores one bit per cell in MLC or TLC NAND. Capacity drops to one half (MLC) or one third (TLC), while endurance and write speed rise sharply. Many industrial eMMC and SSD products let you configure part or all of the device as pSLC, for example through the eMMC enhanced user data area. It is a common middle ground between native SLC cost and TLC endurance. Note that pSLC is not the same as native SLC: the ratings come from the device vendor, so check them per part.
How to estimate whether TLC is enough
Use a simple write budget:
Lifetime writes ≈ capacity × rated P/E cycles ÷ write amplification
For example, an 8 GB TLC device rated at 3,000 cycles with a write amplification of 2 can absorb about 12 TB of host writes. At 5 GB of writes per day, that is roughly 6.5 years before reaching the rating. This example is illustrative only; use the endurance figure (or TBW) from the datasheet and measure your real daily write volume and write amplification. If the margin is thin, increase capacity, move logs to RAM or a separate device, or use pSLC.
Selection guide
- Small, read-mostly firmware: SPI NOR or SLC NAND.
- 1–16Gb with frequent writes and a Linux host: SLC NAND (raw or SPI).
- 8 GB to 1 TB system storage: 3D TLC in eMMC, UFS or an SSD. Budget writes, keep 15–30% free space and consider pSLC for log partitions.
- High temperature or automotive: choose parts rated for the range (industrial or AEC-Q100) and remember that heat shortens retention.
- Long-life programs: dual-source where possible and track PCN/EOL notices from the manufacturer.
Need help choosing NAND?
SUNTEC supplies NAND flash, eMMC and UFS from Kioxia, Samsung, Micron, SK hynix, SanDisk, Winbond and Macronix. Tell us the capacity, interface, temperature range and daily write volume, and we will reply within 1 business day with options. Submit your BOM.
References
- Samsung Newsroom, Samsung starts mass producing industry's first 3D vertical NAND flash (2013)
- Micron, MT29F4G08ABADA 4Gb SLC NAND data sheet (endurance and ECC requirements)
- Winbond, W25N01GV 1Gb serial SLC NAND data sheet (endurance, data retention, on-die ECC)
- congatec, eMMC lifetime application note AN50 (pSLC and enhanced user data area)
- JEDEC, JESD218 SSD requirements and endurance test method