Short answer: An eMCP (embedded multi-chip package) stacks an LPDDR DRAM and an eMMC storage device in one BGA. Use it when board space is tight and you need modest amounts of both, for example a few GB of DRAM and tens of GB of storage, in an IoT gateway, wearable, smart home device or entry-level mobile product. Move to a uMCP (LPDDR plus UFS) when you need more storage throughput, and stay with discrete LPDDR plus eMMC or NAND when you need large or unusual capacity combinations or more freedom to second-source. Before choosing, fix four things: the capacity pair, the DRAM generation and speed, the temperature grade and the package ball map.
eMCP vs discrete LPDDR plus eMMC
An eMCP is not a new kind of memory. It is a package that combines two mature devices, eMMC (NAND plus controller) and LPDDR, so one footprint replaces two.
| eMCP (LPDDR + eMMC in one package) | Discrete (LPDDR + eMMC or raw NAND) | |
|---|---|---|
| Board area and routing | One BGA; short LPDDR connections inside the package | Two or three packages; you own the LPDDR layout and impedance control |
| Capacity flexibility | Fixed capacity pairs set by the manufacturer | Any combination of DRAM and storage |
| Supply and second sourcing | Depends on one ordering code; fewer alternatives | Each device can be second-sourced separately |
| Signal integrity | Consistent, handled inside the package | You tune LPDDR signal integrity and timing |
| Cost | Attractive at low and mid capacities | Better for large capacities or flexible combinations |
| Typical use | Space-limited IoT, wearables, entry mobile, smart devices | Industrial, networking and multi-channel designs that need large memory |
eMCP vs uMCP
Both combine DRAM and storage. The difference is the storage interface. eMMC is half duplex: reads and writes share one bus. UFS is full duplex with command queuing, so throughput and random performance are higher, and so is the cost. Samsung's current public product pages describe the two families like this:
| Samsung LPDDR4X eMCP | Samsung LPDDR5 uMCP | |
|---|---|---|
| Storage interface | eMMC 5.1 | UFS 3.1 |
| DRAM | LPDDR4X, up to 4,266 Mbps | LPDDR5, up to 6,400 Mbps |
| Storage capacity | 16 GB, 32 GB, 64 GB | 128 GB, 256 GB |
| DRAM density | 16 Gb, 24 Gb, 32 Gb (2 GB, 3 GB, 4 GB) | 64 Gb, 96 Gb (8 GB, 12 GB) |
| Package | 144 FBGA or 254 FBGA | 297 FBGA |
eMMC 5.1 storage is limited by the HS400 bus, about 400 MB/s, so a uMCP is the step up for 4K video, heavier applications or on-device AI.
Five checks before choosing an eMCP
- Capacity pair: size the eMMC for system, applications and data, and the LPDDR for the operating system and applications, separately. Then move to the nearest standard pair the manufacturer offers. Unusual pairs are harder to buy and slower to deliver.
- DRAM generation and speed: match what the SoC memory controller supports. LPDDR4X runs its I/O at 0.6 V instead of the 1.1 V of LPDDR4 to save power; check that the SoC supports LPDDR4X before choosing it, and do not pay for a speed the platform cannot use.
- eMMC version and endurance: prefer eMMC 5.1 (HS400, command queuing). For industrial or automotive use, check the endurance figure and whether the part supports a pseudo-SLC area and power-loss protection.
- Temperature grade: consumer, industrial and automotive grades have different ranges. Outdoor IoT and in-vehicle telematics need a wide-temperature or automotive part; take the exact range from the datasheet.
- Package, ball map and channels: eMCP packages come in several ball counts (Samsung's LPDDR4X eMCP uses 144 or 254 balls). When changing part numbers, compare the ball map with the SoC pinout, and check that the number of LPDDR channels matches the memory controller.
Also check the SoC vendor's list of validated memory devices. Platforms such as NXP i.MX, Rockchip, Allwinner, MediaTek and STM32MP publish supported memory lists, and choosing from them avoids most bring-up problems.
Replacing an eMCP that is no longer available
Look for a part that matches on all four points: the same eMMC version, the same LPDDR generation and speed, the same capacity pair and the same package and ball map. For a cross-brand change, also confirm that the SoC platform has validated the new device and that the temperature grade is at least as wide. Examples of Samsung eMCP part numbers on our site are KMDH6001DM-B422 and KMDX60018M-B425; check the exact capacity pair, grade and ball count in the datasheet.
When no matching eMCP is available, a board revision to discrete parts is the robust route: an LPDDR4X device such as Samsung K4UBE3D4AA-MGCL plus an eMMC from Samsung, Kioxia or Micron, chosen independently.
Send us your requirements
Send us the capacity pair, temperature range, SoC platform and yearly volume. We will suggest standard eMCP options, cross-brand alternatives or a discrete LPDDR plus eMMC combination. We reply to routine inquiries within 1 business day. Submit your BOM.
References
- Samsung Semiconductor, eMCP product overview: LPDDR4X eMCP with eMMC 5.1, capacities, DRAM densities, packages and speed
- Samsung Semiconductor, uMCP product overview: LPDDR5 uMCP with UFS 3.1, 297 FBGA