Some STM32F103C8T6 digital inputs can accept 5V signals under the specified conditions, but this does not apply to every GPIO. For a normally powered 3.3V device, verify the FT marking, disable the internal pull-up and pull-down resistors, and check the actual input waveform. Standard I/Os and ADC inputs have different limits. Input tolerance also does not establish a 5V output capability.
1 Match the FT marking to the actual package pin
ST identifies five-volt-tolerant pins with FT in the I/O level column of data sheet DS5319 Rev 20, Table 5. A peripheral name alone does not identify the electrical capability of its pad. Start with the complete order code and the package used on the PCB, then follow the signal from the schematic to the physical device pin.
| LQFP48 position | Data sheet entry | Review decision |
|---|---|---|
| Pin 31 PA10 | FT; includes USART1_RX | Evaluate against the FT digital-input conditions |
| Pin 10 PA0-WKUP | Not FT; includes ADC12_IN0 | Do not apply the FT allowance |
| Pin 7 NRST | Dedicated reset pin | Use the reset-pin electrical requirements |
These three examples are a starting point for a pin review, rather than permission to connect every signal on a development board. A header position is not necessarily the chip pin number. Check the board schematic before using a label printed beside a connector. If firmware remaps a peripheral, review the pin receiving the signal after that remapping, not only the default connection.
For example, a serial adapter transmitting to PA10 presents a different electrical question from one transmitting to another port pin. Record the receive net explicitly. Reusing an earlier UART wiring note without checking its destination can carry an unsupported voltage assumption into a new PCB revision.
2 Check supply state and configuration with the voltage limit
Table 9 specifies an FT I/O input range of −0.3V to 5.5V when 2V < VDD ≤ 3.6V. Its footnote requires the internal pull-up and pull-down resistors to be disabled for an input above VDD + 0.3V. A nominal 5V signal therefore needs both an appropriate pad and an appropriate configuration. The FT label does not replace either check. These are allowed operating input voltages, not the VIH and VIL thresholds used to recognize logic states; check Table 36 for that separate decision.
Keep the conditions attached to the conclusion. This example assumes a device operating normally from a 3.3V supply. It does not authorize a 5V VDD supply. It also does not establish that a signal may remain present while the MCU is unpowered. Review independent supply switching, startup and shutdown as separate interface states, with suitable isolation or translation where the design requires it.
For a standard I/O, Table 9 gives an upper operating input limit of VDD + 0.3V. Selecting a digital-input mode in software cannot turn PA0 into an FT pad. When PA0 is used for an ADC conversion, Table 47 specifies a conversion range from zero to VREF+. In the LQFP package, VREF+ is internally connected to VDDA. Do not interpret digital tolerance as an extension of that analog measurement range.
Also identify the source output type. A push-pull transmitter and a signal pulled high through an external resistor do not create the same operating conditions. If a line changes direction, document which device may drive it in each state. The input-only conclusion here should not be extended to a pin configured as an output, or to an undocumented combination of output drivers.
Absolute maximum ratings answer a different question from normal operating limits. They are stress limits and do not establish reliable operation at the boundary. Review overshoot and undershoot at the receiving pin as well as the nominal high level. A source described as 5V logic may have tolerances or transitions that are not captured by its label.
3 Validate the receive path and the return path separately
Draw the signal direction before reviewing voltage compatibility. For peripheral TX to MCU RX, inspect the MCU input pad, its final configuration and the source waveform. For MCU TX to peripheral RX, use the specifications of that receiving device. Qualify both directions separately, even when the two signals share a connector and nominal supply voltage.
| Review item | Evidence to retain | Conclusion it cannot support |
|---|---|---|
| Pin and firmware | Pad identity, FT classification and final input configuration | Every STM32 pin accepts 5V |
| Signal waveform | High and low levels, overshoot and undershoot at the receiver | A 5V meter reading proves compliance |
| Power sequence | Startup, shutdown and independently powered peripheral states | Normal operation proves powered-off tolerance |
| Return signal | Receiver thresholds and transmitter output conditions | 5V input tolerance provides a 5V output |
For each direction, compare the transmitter’s guaranteed minimum VOH with the receiver’s minimum VIH, then compare its maximum VOL with the receiver’s maximum VIL. The high must exceed the high threshold and the low must remain below the low threshold, with margin for the intended conditions. A nominal supply value is not a guaranteed output level. Use the supply, load current and temperature conditions associated with the specifications; do not compare limits taken from unrelated operating points.
After checking the specifications and schematic, measure at the receiving pin. Apply a valid low state and a valid high state, and record the voltage referenced to the receiver’s ground for each. Then inspect the transitions for overshoot and undershoot. Keep the allowed operating voltage and the logic threshold checks separate: a level may be within the permitted voltage range while still lacking a guaranteed logic interpretation.
For a communications signal, capture the expected signal states and the actual waveform together so the measurement can be associated with the correct net and direction. A logic trace shows the decoded states; use the voltage waveform to assess the levels at the receiver. Include the board revision, source, measurement point, supply state and firmware version in the record. Do not apply an excessive voltage to discover whether a pin survives it. A successful transfer by itself does not establish voltage margin or long-term reliability.
If an intermittent fault follows a firmware change, compare the input configuration before changing components. If it follows a board change, verify the net-to-pad mapping. When the observed high or low is outside the specified limits, resolve that electrical mismatch before treating the fault solely as a protocol or software problem.
4 Carry the interface conditions into the BOM review
When selecting a candidate from the STMicroelectronics parts catalog, retain the exact part number and package alongside the interface requirements. Neither a shared family name nor a matching footprint establishes identical electrical behavior at every pin. Give the engineering reviewer the original schematic net, signal direction, external logic voltage and intended firmware configuration.
For the opposite direction, the guide to driving a 5V SN74HC595N from a 3.3V MCU explains why receiver thresholds need a separate check. It addresses output-to-input compatibility, while this article addresses the STM32 receive pin. Keep those two decisions separate when documenting a complete bidirectional interface.
Keep a proposed replacement separate from an approved replacement in the purchasing record. An inquiry identifies the ordering code, package and quantity being requested; it does not establish board-level compatibility. Record any unresolved powered-off or analog-input requirement precisely, with the affected net and operating state, so engineering can complete the review before a substitute is released. A shortened part description or the words 5V tolerant cannot replace those conditions.
For an STM32F103C8T6 sourcing review, include the receiving pins, external logic voltage and power sequence with the BOM. Check candidate parts against the pin-level limits, firmware settings and return-path thresholds before confirming the selection. Send SUNTEC the full part number, package, quantity and required delivery date, noting any 5V interface conditions that still need review.
Prepared by the SUNTEC Technical Team at Suzhou SUNTEC Electronics Co., Ltd.