Short answer: Most STM32 choices narrow quickly by workload. Use STM32C0 or G0 (Cortex-M0+) for cost-sensitive control, F4 or G4 (Cortex-M4 with FPU) when you need floating-point math, motor control or digital power, H7 (Cortex-M7, up to 480 MHz on STM32H743) for graphics, gateways and heavier signal processing, and L4 when battery life matters. STM32F1 is still a sound choice for extending a proven board, but compare G0 and G4 before you start a new F1 design.
A quick decision path
- Cost-sensitive control or replacing an 8-bit MCU: C0 or G0, such as STM32C031F6P6 or STM32G030F6P6.
- Existing STM32F1 platforms: keep STM32F103C8T6 or STM32F103VET6 where the firmware and board are already proven.
- Floating-point math, audio or more headroom: F4, such as STM32F401CCU6, STM32F411CEU6 or STM32F407VGT6.
- Motor control and digital power: G4, such as STM32G431CBT6, which ST describes as 170 MHz with a math accelerator and medium analog integration.
- HMI, protocol gateways and edge processing: H7, such as STM32H743VIT6.
- Battery-powered products: the ultra-low-power L4, such as STM32L431CBT6.
How the series differ
- STM32F0 (Cortex-M0, 48 MHz): the original entry line. STM32F030F4P6 covers simple control in TSSOP20, and STM32F072CBT6 adds USB, CAN and CEC. For a new low-cost design, look at G0 first.
- STM32G0 (Cortex-M0+, 64 MHz): the successor to F0, with a single power-supply pair and newer peripherals. STM32G071RBT6 has 128 KB flash, 36 KB RAM and an integrated USB Type-C Power Delivery controller.
- STM32C0 (Cortex-M0+, 48 MHz): ST's lowest-cost STM32 line. ST documents pinout compatibility with STM32G0. Treat matching-package C0 and G0 devices as migration candidates; approve an alternative only after checking the exact devices and validating the firmware and board.
- STM32F1 (Cortex-M3, 72 MHz): the first STM32 series, launched in 2007, with the largest body of reference designs and community material. STM32F105RCT6 adds USB OTG FS and two CAN interfaces, a common choice for CAN and USB gateways.
- STM32F4 (Cortex-M4 with FPU and DSP instructions): 84 to 180 MHz in the parts below. F401 and F411 suit compact designs. STM32F407VGT6 (168 MHz, 1 MB flash) adds an Ethernet MAC and a parallel camera interface. STM32F429IGT6 adds an LCD-TFT controller and an external memory controller with SDRAM support for HMI.
- STM32G4 (Cortex-M4 with FPU, 170 MHz): a math accelerator and integrated analog peripherals for motor control and digital power.
- STM32H7 (Cortex-M7): STM32H743 runs at up to 480 MHz with a double-precision FPU, up to 2 MB of dual-bank flash and up to 1 MB of RAM.
- STM32L4 (Cortex-M4 with FPU, 80 MHz): ultra-low-power line for battery-powered devices.
15 common part numbers compared
| Part number | Core / max clock | Flash / RAM | Package | Dhrystone (ST) | Typical use |
|---|---|---|---|---|---|
| STM32C031F6P6 | M0+ / 48 MHz | 32 KB / 12 KB | TSSOP20 | – | Replacing 8-bit MCUs, appliances |
| STM32G030F6P6 | M0+ / 64 MHz | 32 KB / 8 KB | TSSOP20 | – | Low-cost general control |
| STM32F030F4P6 | M0 / 48 MHz | 16 KB / 4 KB | TSSOP20 | – | Existing low-cost designs |
| STM32F072CBT6 | M0 / 48 MHz | 128 KB / 16 KB | LQFP48 | – | Low-cost USB devices |
| STM32G071RBT6 | M0+ / 64 MHz | 128 KB / 36 KB | LQFP64 | – | General purpose, USB Type-C PD |
| STM32F103C8T6 | M3 / 72 MHz | 64 KB / 20 KB | LQFP48 | 1.25 DMIPS/MHz | General industrial control |
| STM32F103VET6 | M3 / 72 MHz | 512 KB / 64 KB | LQFP100 | 1.25 DMIPS/MHz | Larger firmware, more I/O |
| STM32F105RCT6 | M3 / 72 MHz | 256 KB / 64 KB | LQFP64 | 1.25 DMIPS/MHz | USB OTG and dual-CAN gateways |
| STM32F401CCU6 | M4F / 84 MHz | 256 KB / 64 KB | UFQFPN48 | 105 DMIPS | Compact, more performance |
| STM32F411CEU6 | M4F / 100 MHz | 512 KB / 128 KB | UFQFPN48 | 125 DMIPS | Compact, more performance |
| STM32F407VGT6 | M4F / 168 MHz | 1 MB / 192 KB | LQFP100 | 210 DMIPS | Industrial control, Ethernet, camera |
| STM32F429IGT6 | M4F / 180 MHz | 1 MB / 256 KB | LQFP176 | 225 DMIPS | HMI with LCD-TFT and SDRAM |
| STM32G431CBT6 | M4F / 170 MHz | 128 KB / 32 KB | LQFP48 | 213 DMIPS | Motor control, digital power |
| STM32L431CBT6 | M4F / 80 MHz | 128 KB / 64 KB | LQFP48 | 100 DMIPS | Battery-powered devices |
| STM32H743VIT6 | M7 / 480 MHz | 2 MB / 1 MB | LQFP100 | 1027 DMIPS | HMI, gateways, image processing |
The quoted 480 MHz maximum for STM32H743VIT6 is specified in the revision V operating-conditions chapter of ST's DS12110 datasheet. Verify the fitted silicon revision and its applicable voltage-scaling, supply and junction-temperature limits. The V in this ordering code denotes 100 pins, not silicon revision V. Dhrystone figures are ST's published benchmark results, not guaranteed speedups for a particular application.
All 15 were listed as active on ST's product pages when we checked in October 2026. RAM figures follow ST: the 192 KB on STM32F407VG includes 64 KB of core-coupled data RAM, and the 1 MB on STM32H743VI includes 192 KB of TCM RAM. The same part number often comes in other packages and temperature grades, so confirm the full order code against the datasheet before production.
Reading an STM32 part number
Take STM32F103C8T6: F103 is the product line, C the pin count (48), 8 the flash size (64 KB), T the package (LQFP) and 6 the temperature range (–40 to +85 °C). Other common codes:
- Pin count: F = 20, C = 48, R = 64, V = 100, I = 176.
- Flash size: 4 = 16 KB, 6 = 32 KB, 8 = 64 KB, B = 128 KB, C = 256 KB, E = 512 KB, G = 1 MB, I = 2 MB.
- Package: P = TSSOP, T = LQFP, U = UFQFPN, H = BGA.
- Temperature: 6 = –40 to +85 °C; many parts also come in a 7 version for –40 to +105 °C, such as STM32F103C8T7.
The ordering-information table in each series datasheet is the final reference, because a few codes vary between series.
Choosing by application
- Appliances and small control boards: STM32C031 or STM32G030 give you a full Cortex-M0+ toolchain in a TSSOP20 footprint.
- Maintaining an F103 platform: keep the qualified part, secure a traceable supply channel and qualify a backup early (see below).
- Data acquisition with filtering or PID loops: an M4 with FPU (F4 or G4) handles single-precision math in hardware.
- Display HMI: STM32F429 combines an LCD-TFT controller with external SDRAM for modest screens; move to H7 for higher resolutions and richer GUIs.
- Communication gateways: STM32F105 for dual CAN plus USB OTG, STM32F407 for an Ethernet MAC, STM32H743 for more bandwidth and memory.
Migration and backup options
- F0 to G0 is a migration, not a drop-in swap. ST's application note AN5145 explains that STM32G0 uses a single power-supply pair, so the pinout differs from STM32F0 in the same package. The STM32Cube HAL is compatible between the two series, with small differences in the low-layer APIs, so firmware usually ports with a rebuild and a peripheral review, but the PCB has to change.
- Evaluate C0 and G0 migration candidates. STM32C031F6P6 and STM32G030F6P6 share the TSSOP20 package and can be shortlisted for a migration review. ST's AN5969 describes hardware and firmware differences to review; a shared package or compatible pinout alone does not qualify a replacement. The C031 has 12 KB of RAM against 8 KB, while the G030 runs at 64 MHz against 48 MHz. Check the exact pin functions, supply limits, peripherals and clocks, adapt the firmware as needed, and validate the board before approving an alternative.
- A second source for STM32F103C8T6. GigaDevice GD32F103C8T6 is commonly evaluated as a second source in the same LQFP48 package. It is not a firmware-transparent swap: clock limits, flash wait states and some peripheral behavior differ, so requalify the firmware and test on the board. Our STM32F103C8T6 BOOT0, BOOT1 and UART bootloader guide covers one of the checks.
Sourcing
Supply conditions for different STM32 series do not move together, so decide on a primary part and a qualified backup when the project starts rather than during a shortage. Buy through traceable channels and keep the batch and date code records with your incoming inspection. SUNTEC supplies ST STM32 and GigaDevice GD32 MCUs, with BOM quotation and pin-compatible cross-reference; every batch is traceable and inspected before shipment. Browse the ST STM32 and GigaDevice pages.
Send us your BOM
Send the part numbers or BOM, the yearly volume and any series you want to keep. We reply to routine inquiries within 1 business day and return a matched proposal for complex BOMs within 2 business days. Submit your BOM.
References
STMicroelectronics: DS12110: STM32H742xI/G and STM32H743xI/G datasheet (Rev 11; maximum frequency and operating conditions); AN5969: Migrating between STM32G0 and STM32C0 MCUs.
- STMicroelectronics product pages: STM32H743VI, STM32F407VG, STM32F103C8, STM32G030F6, STM32G431CB, STM32L431CB
- STMicroelectronics, STM32C0 series (pinout compatible with STM32G0)
- STMicroelectronics, AN5145: Migration of applications from STM32F0 Series to STM32G0 Series