Quotes within 1 business day
SUNTEC Suzhou SUNTEC
Home / Product Catalog / Serial Interface Transceiver
COMPONENT CATALOG

Serial Interface Transceiver

Browse RS-232, RS-485, RS-422, CAN, and LIN transceiver part numbers. Compare bus requirements and board fit before requesting a quote.

Selection Guide

What to Compare Before Ordering

Start with the bus on the existing board or in the design. Check both the controller-side logic levels and the bus-side electrical requirements. For a replacement, use the exact ordering code to compare the pinout, package, supply, and lifecycle before finalizing the BOM.

Selection dimensionCheck for the complete part number
RS-232Check logic-side voltage, channel count, data rate, and any charge-pump capacitor requirements
RS-485 and RS-422Check duplex mode, bus loading, termination, and isolation where the design requires it
CANCheck the required bus rate, the data phase rate for CAN FD, host I/O voltage, and standby or wake behavior
LINCheck bus supply, the required data rate, and how the node sleeps or wakes
Ordering detailsCheck the full part number and suffix, pinout, package, temperature grade, and manufacturer lifecycle

Manufacturer references: ADI MAX3232 · TI RS-485 Design Guide · NXP TJA1042 · NXP TJA1027

Brands

Brands in This Catalog

Part Numbers

Listed Part Numbers and Specifications

Part numbers: 18 · Page 1 / 1

Part No.BrandSeriesSpecificationApplicationQuote
SN65HVD230DTexas InstrumentsInterface (CAN)3.3V CAN transceiverIndustrial / CAN busQuote →
SN75176BPTexas InstrumentsInterface (RS485)RS485 transceiver (classic)RS485 busQuote →
SN65HVD75DTexas InstrumentsInterface (RS485)3.3V RS485 transceiverIndustrial communicationQuote →
MAX485ESAAnalog DevicesRS485Half-duplex RS485 transceiver (classic)Industrial / RS485 busQuote →
MAX232CSEAnalog DevicesRS232RS232 line driver / receiver (classic)Serial communicationQuote →
MAX3232CSEAnalog DevicesRS232 (3.3V)3V RS232 transceiverLow-voltage serialQuote →
MAX3485ESAAnalog DevicesRS485 (3.3V)3.3V RS485 transceiverLow-voltage industrial communicationQuote →
ADM2483BRWZAnalog DevicesIsolated RS485Isolated RS485 transceiverIndustrial / energy-storage busQuote →
MAX490ESAAnalog DevicesRS485/422 Full-duplexFull-duplex transceiverRS422 communicationQuote →
ADM485JRZAnalog DevicesRS485RS485 transceiverIndustrial communicationQuote →
MCP2551-I/SNMicrochipCAN Transceiver5V CAN transceiverCAN physical layerQuote →
TJA1050TNXPCAN TransceiverHigh-speed CAN (classic)Industrial / CAN busQuote →
TJA1042TNXPCAN TransceiverCAN FD transceiver (mainstream)CAN FD busQuote →
TJA1051T/3NXPCAN TransceiverBasic high-speed CANCAN busQuote →
TJA1040TNXPCAN TransceiverHigh-speed CAN with standbyCAN busQuote →
TJA1043TNXPCAN TransceiverCAN with sleep / diagnosticsAutomotive / industrial CANQuote →
TJA1057GTNXPCAN Transceiver3.3V-compatible CAN FDLow-voltage CANQuote →
TJA1027TNXPLIN TransceiverLIN bus transceiverBody electronics / industrial LINQuote →
FAQ

Procurement Questions

Can I replace an RS-232 transceiver with an RS-485 device if both connect to a UART?

No. A UART connection does not make the bus sides equivalent. RS-232 uses single-ended signaling, while RS-485 uses differential signaling and supports multipoint buses. Changing between them requires an appropriate interface conversion or circuit redesign, including direction control where the selected RS-485 arrangement needs it.

Analog Devices reference

Does a CAN transceiver replace a CAN controller?

No. A standalone CAN transceiver provides the electrical interface between a CAN protocol controller and the bus. The controller handles the CAN protocol. Check whether your MCU already contains the required CAN controller; otherwise, evaluate an external controller or a device that explicitly integrates both functions.

NXP reference

Will fitting a CAN FD transceiver upgrade a Classical CAN node to CAN FD?

No. A CAN FD transceiver does not add CAN FD protocol support to a Classical CAN controller. Verify that the controller and firmware support FD frames and the intended bit timing. Separately check the transceiver's data-phase capability and logic interface, then validate operation on the intended network.

Texas Instruments reference

Request a Quote by Full Part Number

Include quantities and the requirements that matter for your design.

Request a Quote

Fields marked * are required. Your details are only used to reply to your inquiry.

Excel, CSV, PDF, TXT, PNG, JPG or ZIP — up to 3 files, 5 MB each, 10 MB in total.

By submitting, you agree that we use these details to reply to your inquiry as described in our Privacy Policy.

✓ Inquiry received. We reply to routine RFQs within 1 business day and provide a sourcing proposal for complex BOMs within 2 business days. Weekends and public holidays are excluded. These are response and proposal times, not shipping times; lead times are confirmed per order. Urgent? Message us on WhatsApp →
Free BOM Review

Send Us Your BOM

Paste your part list or email an Excel BOM. We reply to routine RFQs within 1 business day and provide a sourcing proposal for complex BOMs within 2 business days. Weekends and public holidays are excluded. These are response and proposal times, not shipping times; lead times are confirmed per order.

  • ✓
    PriceVolume-tiered pricing with currency and tax terms
  • ✓
    Lead TimeAvailability and split-delivery options
  • ✓
    Cross ReferencePin-compatible and spec-compatible alternatives
  • ✓
    Risk NotesEOL, shortage and price-increase alerts with stocking advice

Or email your Excel BOM to suntec@suntecele.com with quantities and target delivery date.

GET QUOTE
Call WhatsAppBOM Quote