Steps in an LM358P sine-wave output do not prove crossover distortion. First check the input common-mode range and available output swing. Then change amplitude, frequency and loading separately. Compare the peaks, waveform slope and local step. Check whether the disturbance follows output-current demand. The output crossing zero volts is not sufficient evidence.

1. Establish a baseline and check the operating range

Use the TI LM358P documentation. Do not apply LM358B typical curves to this device. Capture input and output together with DC coupling. Record the supply at the IC and both input-pin voltages. Include amplitude, DC offset, frequency, feedback connections and the complete load circuit. If the input already has a kink, investigate the source first.

ObservationMeasure firstControlled comparison
Flat peaks or troughsInput range, actual output peaks and supplyReduce amplitude at fixed offset
A local plateau or stepEvent timing and load return voltageTrace output-current paths
A sustained slope limitAmplitude, frequency and output slopeLower frequency at fixed amplitude

Calculate the required closed-loop output, including its DC level. Compare both input voltages and the requested output with the applicable operating conditions. Supply rails alone do not establish the usable input and output ranges. Resolve any range violation before investigating crossover. An output resistor cannot replace this check.

Save a full-cycle capture and an expanded view of the step. Keep the time base, channel scales, coupling and probe settings with them. AC coupling removes the DC component. Its displayed zero line cannot establish the actual output voltage relative to ground or the load reference.

Use the table to select the next measurement. A local step and peak clipping can coexist. Record each feature separately so that removing one does not hide the other.

2. Compare amplitude, frequency and loading separately

Change one condition at a time. Restore the baseline before starting the next comparison. Changing supply, gain and loading together obscures which change caused the improvement.

  1. Reduce input amplitude at fixed frequency and DC offset. Compare the peaks and local step. If the peaks recover but the step remains, keep the two observations separate.
  2. Restore amplitude, then lower frequency. Compare the sustained output slope and the short disturbance. Improvement alone does not distinguish slew-rate limitation from crossover behavior.
  3. Where safe, change or temporarily isolate the following load. Retain the feedback connection. Record the disconnected branch, its return voltage and the resulting waveform. Improvement under lighter loading does not establish device damage.

Sections 4.3–4.5 of TI application note SLOA277B describe the legacy output stage changing source and sink drivers. The note shows the associated delay and an example with positive output voltage but reversing load current. Check current paths rather than assuming that crossover occurs at zero output voltage. The illustrated response times are not guaranteed limits for another circuit.

For a resistive branch, use its terminal voltages and resistance to determine current direction. Include feedback branches in total output demand. A return to an intermediate reference differs from a return to ground. An active following circuit may drive current back into the output. Analyze that circuit rather than treating it as a fixed resistor.

External current reversal does not locate the exact internal driver-switching threshold. Voltage traces and circuit calculations can support a crossover explanation. They do not constitute a measurement of the internal transition.

For intermittent steps, record the following circuit’s state. Trigger around the disturbance and retain individual acquisitions alongside any averaged view. Testing only while the following stage is idle can miss the reported condition.

3. Select a correction and check the consequences

Candidate changeVerify togetherConclusion to avoid
Reduce amplitude or adjust offsetInput range, output peaks and required gainA positive offset eliminates crossover
Change the return or add a bias loadCurrent over the cycle, dissipation and swingOne pulldown value fixes every board
Change the device or output arrangementFull part number, pinout and signal requirementsA familiar family name ensures substitution

A pullup or pulldown load may keep one output driver active. Select the load from the current demand across the full signal cycle. Include signal extremes, feedback current and relevant states of the following circuit. Check resistor dissipation, amplifier loading and output headroom. A resistor value copied from another circuit does not establish these conditions.

After changing the offset, recheck both input-pin voltages and the required output excursion. A positive output can still encounter reversing current. The load may return to another reference or actively supply current to the output.

Define distortion, supply, gain and load requirements before selecting another device. The related LM324N appears in the same application note. That does not establish interchangeable pinouts, recovery behavior or board suitability. Check candidates in the TI device catalog against their own specifications.

4. Retest the original circuit and record acceptance

Restore the original amplitude, offset, frequency and actual following circuit. Repeat the captures with the baseline measurement settings. Record output peaks separately from step magnitude and duration. Check whether reducing the step introduced clipping elsewhere. A light-load improvement is not a pass with the normal load connected.

Test the supply, signal and load conditions required by the project. Keep the schematic version and the change made between the original and revised captures.

Use the specified acceptance method. A visually smooth sine wave is not a measured distortion percentage. For a time-domain requirement, record the specified amplitude and recovery limits with the observation. Separate symptom reproduction, improvement and compliance with the final requirement. If the original fault cannot be reproduced, report that limit instead of claiming a repair.

For an LM358P signal-conditioning requirement, record amplitude, offset, frequency and the load return connection. Check candidate devices at the same supply, feedback configuration and actual load for distortion and usable output swing. For a SUNTEC quotation, provide the complete part number, quantity and requested delivery date with those circuit conditions.

Prepared by the SUNTEC Technical Team at Suzhou SUNTEC Electronics Co., Ltd.